Search results for "010301 acoustics"
showing 10 items of 130 documents
Generalised bisection method for optimum ultrasonic ray tracing and focusing in multi-layered structures
2021
Ultrasonic testing has been used for many decades, proving itself very efficient for detecting defects in many industrial sectors. The desire to apply ultrasonic testing to geometrically complex structures, and to anisotropic, inhomogeneous materials, together with the advent of more powerful electronics and software, is constantly pushing the applicability of ultrasonic waves to their limits. General ray tracing models, suitable for calculating the proper incident angle of single element probes and the proper time delay of phased array, are currently required. They can support the development of new imaging techniques, as Full Matrix Capture and Total Focusing Method, and the execution of …
A combined three-dimensional digitisation and subsurface defect detection data using active infrared thermography
2016
International audience; In recent years, NonDestructive Testing (NDT) systems have been upgraded with three-dimensional information. Indeed, combine the three-dimensional and thermal information allows a more meaningful analysis. In the literature, the data for NDT and three-dimensional (3D) reconstruction analysis are commonly acquired from independent systems. However, the use of two such systems leads to error analysis during the data registration. In an attempt to overcome such problems, we propose a single system based on active thermography approach using heat point-source stimulation to get the 3D digitization as well as subsurface defect detection. The experiments are conducted on s…
A fully-digital realtime SoC FPGA based phase noise analyzer with cross-correlation
2017
We report on a fully-digital and realtime operation of a phase noise analyzer using modern digital techniques with cross-correlation. With the advent of system on chip field-programmable gate arrays (SoC FPGAs) embedding hard core central processing unit, coprocessor and FPGA onto a single integrated circuit, the building of sensitive analysis devices for Time & Frequency research is made accessible at virtually no cost and benefits from reconfigurability. Used with high-speed digitizers we have successfully implemented a four-channel system whose preliminary results at 10 MHz shows a residual white noise floor < −185 dBrad2/Hz up to 5 MHz off the carrier, and flicker < −127 dBrad2/Hz using…
Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel
2019
Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …
Evaluation of Vertical Fatigue Cracks by Means of Flying Laser Thermography
2019
The present paper proposes a new procedure to analyze the temperature field distribution during Flying Laser Spot and Laser Line Thermographic scanning (FLST, FLLT) of metallic components, in order to detect vertical surface cracks. The methodology exploits the changes in the temperature field produced by a vertical crack, acting as a barrier towards heat diffusion, when the laser approaches the defect. A number of small regions of interests (ROIs) is placed nearby and around the laser source. The average temperature from each ROI is then monitored during the laser scanning. Vertical cracks can be detected by analyzing and comparing the temperature fluctuations from each ROI when the laser …
B-Scan image analysis for position and shape defect definition in plates
2016
Definition of size, shape and location of defects into a mechanical component is of extreme importance in the manufacturing industry in general and particularly in high-tech applications, and in applications that can become dangerous due to the structural failure of mechanical components. In this paper, a laser-UT system has been used to define position and shape of internal defects in aluminum plates. An infrared pulsed laser is used to generate ultrasonic waves in a point of the plate and a CW laser interferometer is used as receiver to acquire the out-of-plane displacements due to the ultrasonic waves in another point of the plate. The method consists of acquiring a B-Scan map on which s…
Experimental investigation of the effect of moisture on the acoustic properties of lightweight substrates used in green envelopes
2021
International audience; Substrates are used in green walls and roofs to supply air and water to the roots of the growing plants. These substrates are porous with micropores which store water and macropores which facilitate drainage and air entry. Effect of moisture on acoustic absorption is studied for two lightweight substrates: coir dust and perlite. Measurement of dry and moistened substrates are conducted to evaluate their effective speed of sound, attenuation, characteristic impedance, compressibility and density between 100 Hz and 1000 Hz using an impedance tube and the three microphone-two load method. Effect of moisture on these quantities is found to depend strongly upon the intera…
Cross-correlation of whitened vibration signals for low-speed bearing diagnostics
2019
Abstract Rolling-element bearings are crucial components in all rotating machinery, and their failure will initially degrade the machine performance, and later cause complete shutdown. The period between an initial crack and complete failure is short due to crack propagation. Therefore, early fault detection is important to avoid unexpected machine shutdown and to aid in maintenance scheduling. Bearing condition monitoring has been applied for several decades to detect incipient faults at an early stage. However, low-speed conditions pose a challenge for bearing fault diagnosis due to low fault impact energy. To reliably detect bearing faults at an early stage, a new method termed Whitened …
Integrated GNSS/IMU Hub Motion Estimator for Offshore Wind Turbine Blade Installation
2019
Abstract Offshore wind turbines (OWTs) have become increasingly popular for their ability to harvest clean offshore wind energy. Bottom-fixed foundations are the most used foundation type. Because of its large diameter, the foundation is sensitive to wave loads. For typical manually assisted blade-mating operations, the decision to perform the mating operation is based on the relative distance and velocity between the blade root center and the hub, and in accordance with the weather window. Hence, monitoring the hub real-time position and velocity is necessary, whether the blade installation is conducted manually or automatically. In this study, we design a hub motion estimation algorithm f…
Autonomous ultrasonic inspection using Bayesian optimisation and robust outlier analysis
2020
The use of robotics is beginning to play a key role in automating the data collection process in Non Destructive Testing (NDT). Increasing the use of automation quickly leads to the gathering of large quantities of data, which makes it inefficient, perhaps even infeasible, for a human to parse the information contained in them. This paper presents a solution to this problem by making the process of NDT data acquisition an autonomous one as opposed to an automatic one. In order to achieve this, the robotic data acquisition task is treated as an optimisation problem, where one seeks to find locations with the highest indication of damage. The resulting algorithm combines damage detection tech…